Showing posts with label band. Show all posts
Showing posts with label band. Show all posts
Friday, November 8, 2013
Simple 5 Band Equalizer
This circuit uses a single chip, IC BA3812L to make 5 band graphic equalizer in audio hi-fi system. BA3812L IC is a 5-point graphic equalizer that has all functions integrated on a single IC. This IC is composed of five tone control circuit and input and output buffer amplifier. BA3812L have low distortion, low noise, and wide dynamic range, and is ideal for a variety aperanti Hi-Fi stereo. He also has a wide operating voltage range (3.5V to 16V), meaning he could be adapted for use on most stereo equipment.
The five center frequencies are independently set using external capacitors, and therefore act as an output stage buffer amplifier and tone control section is a series of its own, it is possible to do fine control over the frequency bandwidth. By using two BA3812Ls, you can create a 10-point graphic equalizer. Great header and pieces can be set by external components.
The recommended power supply of 8V, but this circuit can work well for supply voltage 9V. Limit the maximum voltage is 16V.
The circuit is given in the diagram operates in around 5 frequency bands:
100Hz , 300Hz , 1kHz , 3kHz , 10kHz
Thursday, November 7, 2013
Simple 5 Band Equalizer
This circuit uses a single chip, IC BA3812L to make 5 band graphic equalizer in audio hi-fi system. BA3812L IC is a 5-point graphic equalizer that has all functions integrated on a single IC. This IC is composed of five tone control circuit and input and output buffer amplifier. BA3812L have low distortion, low noise, and wide dynamic range, and is ideal for a variety aperanti Hi-Fi stereo. He also has a wide operating voltage range (3.5V to 16V), meaning he could be adapted for use on most stereo equipment.
The five center frequencies are independently set using external capacitors, and therefore act as an output stage buffer amplifier and tone control section is a series of its own, it is possible to do fine control over the frequency bandwidth. By using two BA3812Ls, you can create a 10-point graphic equalizer. Great header and pieces can be set by external components.
The recommended power supply of 8V, but this circuit can work well for supply voltage 9V. Limit the maximum voltage is 16V.
The circuit is given in the diagram operates in around 5 frequency bands:
100Hz , 300Hz , 1kHz , 3kHz , 10kHz
Saturday, October 26, 2013
3 Band Tone Control with LF351
3 Band Tone Control circuit uses an op-amp as an amplifier end. Tone Control circuit is a regulator of tone bass, midrange and treble or 3 band called because it can set the three tones. Filter circuit is applied to the series of "Tone Control 3 band" This type baxandal like the title of this article.
Results filtering regulator tone or tone control baxandal type is good, because there is no signal level is wasted directly into the ground. Range frequency tones generated from Tone Control 3 band was determined by the configuration of the R and C of the filter section baxandal. As an amplifier on Tone Control The set of three band use traditional IC LF351 has slewrate high and high input impedance. For more details, series 3 Band Tone Control as follows.
Figure Series 3 Band Tone Control
3 Band Tone Control circuit above using LF351 Op-Amp is used to strengthen the signal after filtering by the filter process baxandal. Level tone Bass, Midrange and Treble settings are determined by potensio R1, R2 and R3. Frequency filter in the circuit above baxandal to 50 Hz bass tone, tone Midrange 1 KHz and 10 KHz for Treble tone.
Wednesday, September 25, 2013
Two Band Radio Schematic
This TRF receiver covers the AM broadcast, band and longwave bands (used in Europe and Asia for broadcasting). A loop antenna is used for reception and an external antenna can be connected. Frequency coverage is 150 to 1600 kHz.
Two-Band Radio Circuit Diagram
Two-Band Radio Circuit Diagram
Subscribe to:
Posts (Atom)